In order to study the behaviour of a notch specimen under plane mixed mode I +II, a Brazilian disc specimen weakened by U-notch located at the edge of disc is considered. A high-strength steel material was used for the disc specimen subjected to diametral compressive loading. A local approach represented by strain energy density approach based on determination of mean value of the strain energy density (that is over a given finite-size volume surrounding the highly stressed regions near the notch tip) was utilized. A finite element analysis by cast3m code have been undertaken in order to determine the evolution of the stress intensity factors and averaged strain energy density for different location of notch from the axis of force application. Variations of radius and angle of notch will cause disturbance in the stress field and local energy in the vicinity of the notch tip. The results of finite element computations were expressed as mathematical relations showing the influence of notch position and its radius on stress intensity factors and averaged strain energy density. The reduction of the angle increases the local energy unlike the increase of the radius tends to reduce it.

Fatigue crack growths of a corner crack emanating from a pinhole of a solid cylinder subjected to cyclic torsion loading were simulated using a Dual-Boundary Element Method (DBEM) based software. For a given crack aspect ratio a/c, larger Mode I stress intensity factor (SIF) was observed at a larger pinhole diameter. Any given initial crack aspect ratio a/c would evolve towards unity. The final evolving crack aspect ratio a/c was shown to be larger than 1. For the same given initial crack length a, a smaller crack depth c was found to result in a shorter fatigue life. A shorter fatigue life yielded a larger orientation angle of the crack growth path.

ABAQUS/Standard is a powerful finite element program designed for general use in nonlinear problems. The paper touches only one aspect of usage of the software, namely a constitutive modelling of slightly compressible hyperelastic materials. It begins with a discussion of a well-known approach of describing slight compressibility in the context of the stored energy function. Basic equations of continuum mechanics are presented as well. The main part of the work concerns an implementation of one of the presented models. To this end, the UHYPER user subroutine is employed. Analytical formulas for a few simple, homogeneous deformation states are given which allow verifying numerical results. Finally, a couple demonstration examples with nonhomogeneous deformations are presented as an attempt at motivating applications in engineering.

There are huge amounts of emissions associated with construction industry during its different stages from cradle till building demolition. This study presents a methodology that integrates multi-objective optimization and multi-criteria decision making (MCDM) in order to enable construction decision-makers to select the most sustainable construction alternatives. Four objectives functions are investigated, which are: construction time, lifecycle cost, environmental impact and primary energy in order to construct the Pareto front. A novel hybrid MCDM is designed based on seven multi-criteria decision making techniques to select the best solution among the set of the Pareto optimal solutions. Sensitivity analysis is performed in order to determine the most sensitive attribute and construction stages that influence environmental emissions. The analysis illustrates that WSM, COPRAS and TOPSIS provided the best rankings of the alternatives, primary energy is the most sensitive attribute for different MCDM methods. Moreover, PROMETHEE II is the most robust MCDM method.

Synthesis of 2H and 3C-polytype silicon carbide nanowhiskers mixture of silicon dioxide and carbon was performed by carbothermal reduction process. The reaction temperature for synthesis of 2H-SiC was varied from 1350 C to 1650 C and for the 3C-SiC this range was varied from 1450 C to 1650 C. Scanning Electron Microscopy (SEM) analyses showed that nanowhiskers structures of both 2H-SiC and 3C-SiC polytypes has a size up to 100 nm in diameters and several microns in length. However, the orientation and pattern of grains were different in both structures. While for 3C-SiC polytype, the shape has been classified as SiC majorly grew along [101] plane by X-ray Diffraction pattern and finalized by Raman shift peaks at 799 and 959 cm-1, the shape of 2H-polytipe silicon carbide was categorized as SiC majorly grown along [111] plane confirmed by Raman shift peak at 799 and 963 cm-1. The mechanism of vaporgas interaction was also suggested and discussed for both SiC nanowhiskers polytypes.

The growing convolution of industries and the need for corporate business survival has created a cognizance dilemma on the nexus of earnings management and managerial compensation paradigm, especially in developing nations. Hence, this paper sought to examine the nexus of earnings management and managerial compensation in Nigerian manufacturing firms. The study collected panel data from audited annual financial reports of six selected manufacturing firms listed in the Nigeria Stock Exchange, covering the period from, 2012-2019. The data were analyzed using descriptive statistics, correlation and Panel Regression Model. The findings indicate that earnings management is a significant determinant of managerial remuneration. Therefore, the study concludes that managing earnings of firms has a positive significant relationship with executive remuneration, and as such compensation should be tied to performance of the firm in real values.

Composites prepared by Single Wall Carbon Nano-tube (SWCNT) as well as Nylon assume a vital part in practical applications as in ultrastrong lightweight materials, vehicle and flying machine parts. In the present work, the influence of aspect proportion (l/d) on the longitudinal Young's modulus (E11) as well as transverse modulus (E22) for the SWCNT/Nylon 66 composite have been critically analyzed through utilizing tools of Molecular Dynamics (MD) simulations. Materials Studio 8.0 simulation software utilized in the current study for finding Young modulus. Aspect proportion (l/d) of used CNT in the composite was ranged from l/d = 5 up to l/d = 30 while the fraction of volume (Vf) of the CNT had been kept constant at 8%. Results demonstrated however that the lengthwise Young's modulus for the current composite increment essentially by expanding the aspect ratio (l/d) of Nano-tube while the change in transverse modulus with fluctuating perspective proportion was not exceptionally noteworthy. The results of the simulation have been consequently matched with the Mori-Tanaka model as well as the Finegan model.

As archipelagic region, an effort to effectively enhance and accelerate the development of each sub-districts to boost the rapid development of Southeast Maluku district in Indonesia cannot happen as long as the local government fails to identify the real potentials and power in fisheries sector of each sub-districts. Identification of each sub-district fisheries top sub-sector has to be based on the human resources, natural resources, infrastructure, current and potential market, current policy of local and central government. A multi-criteria decision making (MCDM) is one of the powerful tools to provide a better result based on complicated factors involved. This paper proposed an integrated MCDM, to tackle the complicated factors in order to provide the best commodities on each sub-districts. Bottom-up concept was used to have a comprehensive result, by combining Fuzzy logic with Analytical Hierarchy Process (AHP) to measure the factors using fuzzy logic with Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) for determining the top sub-sector in fisheries. For comprehensive assessment of macro factors the study used experts ranging from government, scientists, practitioners to NGOs. On the other hand, for micro factors the survey used field instructor, field officer, fishers and farmers. The results provide a guideline for local and central government to form a better policy regarding the development of each sub-district including farmers, fishers and coastal communities in each sub-district to focus on commodities that benefited their regions’ resources and coastal community’s capabilities. By doing so, we hope to contribute on crafting an integrated and collective path on reaching the goal which is the welfare of coastal region.

The study examines the relationship between money supply and inflation in Vietnam in the period of 2005-2021. The relationship between money supply and inflation is addressed in economic theories and models and has been studied by many experts in different economies in different periods. To examine the relationship between money supply and inflation in Vietnam in the period of 2005-2021, the research team collected data on money supply and inflation rate, then analyzed this relationship during three periods of 2005-2011, 2012-2019 and 2019-2021. Next, the research team collected data on money supply (MS - total means of payment) and consumer price index (CPI), quarterly data from the first quarter of 2005 to the fourth quarter of 2021 and uses Eviews 8 software for analyzing. The research team uses a linear regression model to evaluate the impact of money supply growth (GMS) on consumer price index (CPI), a variable representing the inflation rate, of Vietnam during the research period. The model results support the view that money supply growth and past inflation are among the factors affecting inflation in Vietnam. From the research results and the actual money supply, the money supply growth rate as well as the inflation rate in Vietnam during the research period, the research team makes some policy recommendations to achieve the targets of supporting economic recovery, controlling inflation, stabilizing the macro-economy in Vietnam after the Covid-19 pandemic.

Mastic mortar, i.e. a mixture of bitumen and very fine filler particles (i.e. aggregate fine particles smaller than 0.063 mm), can significantly co-influence not only rheological properties of the processed asphalt mixture, but also the visco-elastic properties of compacted asphalt layers including resistance against crack formation. Nevertheless, the number of scientific studies dedicated to this topic in detail, is very limited. The aim of this work is to determine the basic rheological properties of these mastic materials using a dynamic shear rheometer, in particular concentrating on the petrographic origin of the filler particles. Fourteen filler types were selected and mixed with paving bitumen 70/100 in various ratios. Petrographic composition of the individual fillers was determined using powder X-ray diffraction analysis. Attention was given especially to the effect of the presence of mica on the filler and mastic properties. Filler properties were analyzed using the voids of dry compacted filler test so-called "Rigden voids" and the delta ring and ball test. Mastic mortars prepared in a laboratory were subjected to multiple stress creep and recovery test and oscillation measured at 60 °C in a dynamic shear rheometer. Results show that using dynamic shear rheometer to determine the properties of these materials is advantageous. Petrographic origin of the filler to a great extent affects the behavior and properties of the mastic mortar, especially its stiffening effect. Limestone filler stiffened the bituminous binder the least and reference materials, containing high ratio of mica, stiffened the binder the most.